Acura Professionals

Acura
 
Patches
  • New award patches are now included with Tenure (for all Parts and Service management and staff) and Master Technician awards.
  • Each dealer will receive 5 patches for each of their award winners, unless they have requested to receive specific numbers instead. Dealers may request specific numbers of patches to receive for their award winners by contacting professionals@ahm.honda.com
  • Dealers may order additional patches for staff who have earned Tenure or Master Technician awards in the past by contacting professionals@ahm.honda.com
  • Adding patches to your work uniforms
    • We highly recommend having a professional (tailor, alterations service, etc.) add the patches to your work uniforms.
    • The key is consistency - place patches in the same locations on the shirt for all staff.
    • Preferred patch locations:
      • Tenure patch - Left sleeve (shown above)
      • Master Technician patch - Left sleeve or Chest (right side) if left sleeve is not available
 
Order Code: TM
Master Technician
3.5" wide x 2.5" tall
$1.00 each

Order Code: T3
Tenure – 3 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T5
Tenure – 5 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T10
Tenure – 10 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T15
Tenure – 15 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T20
Tenure – 20 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T25
Tenure – 25 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T30
Tenure – 30 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T35
Tenure – 35 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T40
Tenure – 40 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T45
Tenure – 45 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T50
Tenure – 50 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T55
Tenure – 55 years
3.5" wide x 2.5" tall
$1.00 each
Order Code: T60
Tenure – 60 years
3.5" wide x 2.5" tall
$1.00 each
We highly recommend having a professional
(tailor, alterations service, etc.)
add the patches to your work uniforms.
If you choose to add the patches yourself, please follow the Guidelines below.

Recommended Guidelines for Adding Patches

Things You'll Need
  • Heat transfer patch
  • Iron
Instructions
  1. Set the iron to the hottest setting. Disable the steam setting and use a dry iron.
  2. Once the iron is heated, press (iron) the area on the receiving item where the transfer is to be placed.
  3. Position the transfer on the pressed area of the receiving item.
  4. Press and hold the iron lightly on the patch for a few seconds. The heat from the iron will activate the adhesive substance and permanently attach the transfer to the cloth.
  5. Slightly move the iron back and forth over the transfer for about one minute.
  6. Check the edges of the transfer. If the edges are not secured to the cloth, repeat Steps 4 and 5 until the transfer is securely adhered to the cloth. Remember, the patch must be able to endure several launderings so make sure there is good contact between the transfer and the cloth.
Tips & Warnings
The edges may loosen after a few washings. To avoid this, it is recommended that you stitch the patch onto the garment with a needle and thread.

Stop immediately and remove the iron from the surface if you notice a burning smell. The smell of burning cloth means either the cloth or the transfer is melting.


© 2018 American Honda Motor Co., Inc.